![]() ![]() L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 enabling early BRESP for Cortex-A9 NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 Preemptible hierarchical RCU implementation. SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1įtrace: allocating 38831 entries in 114 pages Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) PID hash table entries: 4096 (order: 2, 16384 bytes)ĭentry cache hash table entries: 131072 (order: 7, 524288 bytes) Kernel command line: console=ttymxc0,115200 init=/init video=mxcfb0:dev=ldb,fbpix=RGB32,bpp=32 video=mxcfb1:off video=mxcfb2:off video=mxcfb3:off vmalloc=128M nsole=ttymxc0 consoleblank=0 androidboot.hardware=freescale cma=320M linux=permissive ntiguousSize=33554432 loop.max_part=7 buildvariant=userdebug rialno=1d2229d4ea997119 androidboot.btmacaddr=1d:22:29:d4:ea:99 androidboot.soc_type=im圆q androidboot.storage_type=emmc androidboot.boottime=1BLL:0,1BLE:5054,KL:0,KD:0,AVB:925,ODT:0,SW:0 androidboot.bootreason=watchdog androidboot.verifiedbootstate=green androidboot.slot_suffix=PARTUUID=621ee45e-e923-4fc2-aa1d-6fd0bc488995 _version=1.1 _state=locked _alg=sha256 =2944 =999aac0a122a2b1bed2062a477c07a76e66b4e5230ca8c80a4f6e3558d9127c6 androidboot.veritymode=enforcing androidboot.dtbo Percpu: Embedded 18 pages/cpu s41228 r8192 d24308 u73728īuilt 1 zonelists, mobility grouping on. OF: fdt: Machine model: i.MX6 AOSP 9.0 Board Linux version 4.14.98 (gcc version 4.9.x 20150123 (prerelease) (GCC)) #44 SMP PREEMPT Mon Jan 27 19:20:ĬPU: ARMv7 Processor revision 10 (ARMv7), cr=10c53c7dĬPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Using Device Tree in place at 14f00000, end 14f112e0 Kernel load addr 0x14008000 size 8924 KiB No panel detected: default to Hannstar-XGA *** Warning - bad CRC, using default environment ![]() MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 please find below error logs,ĬPU: Freescale i.MX6Q rev1.3 996 MHz (running at 792 MHz)ĬPU: Extended Commercial temperature grade (-20C to 105C) at 38C and I build the source and trying to boot from eMMC.įacing issue in fstab mounting point. Clear the flag to boot into Safe Mode, so the system will boot into normal mode.Īfter disabling RAID by following the instructions on that website, Windows worked with RAID disabled, and I was able to install Ubuntu successfully.I am using AOSP9 and IMX6Q SABRESD Board.Windows will boot into Safe Mode automatically. Exit BIOS settings and boot to Windows.Reboot and enter the BIOS settings to disable RAID.Boot into windows, and set a flag to boot into Safe Mode on the next restart.Here is a summary of the instructions to the best of my understanding: I tried disabling RAID in the BIOS but then Windows would not boot.Īfter some searching around, I found a website with instructions on how to disable RAID in Windows. It turned out to be because I had RAID enabled for the SSD. I had a similar problem trying to install Ubuntu (via USB) alongside Windows 10: the Ubuntu installer did not recognize my SSD and only found the USB drive I was installing from. (Add four spaces to the beginning of each line of that output to preserve columnar output.) If you think this is the source of the problem and if FixParts can't fix it or if you're wary of using FixParts, post the output of sudo fdisk -l /dev/sda. Other problems may require more specialized and manual repairs. My FixParts program (part of the gdisk package in Ubuntu) will correct many of these problems in an automatic or semi-automatic mannger see its Web page for details. If any exist, it usually reports the disk as being empty. A damaged partition table - The libparted library (upon which the Ubuntu installer relies) is extremely sensitive to partition table problems.If you erase RAID data when the system is actually using RAID, the result can be problems accessing your disk at all. You can usually fix this problem by typing sudo dmraid -E -r /dev/sda however, you should be very sure that you're not currently using software RAID. Leftover software RAID data - If the disk had been (or is being) used with software RAID, leftover RAID data can confuse the Ubuntu installer.This symptom is usually caused by one of two problems: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |